40-65 mould

Thread Rating:

Thread Modes

40-65 mould

01-25-2024, 04:50 PM,

#30

Steveu
Guest

RE: 40-65 mould

Yup, I added one to the original design so I could get a full groove at the case mouth/ transition area.

« Next Oldest | Next Newest »

Messages In This Thread

40-65 mould - by Steveu - 08-24-2023, 09:02 AM

RE: 40-65 mould - by Kurt - 08-24-2023, 10:05 AM

RE: 40-65 mould - by Don McDowell - 08-24-2023, 11:43 AM

RE: 40-65 mould - by Don McDowell - 08-24-2023, 11:45 AM

RE: 40-65 mould - by Steveu - 08-24-2023, 09:53 PM

RE: 40-65 mould - by Kurt - 08-24-2023, 10:16 PM

RE: 40-65 mould - by Don McDowell - 08-25-2023, 09:03 AM

RE: 40-65 mould - by Kurt - 08-25-2023, 10:21 AM

RE: 40-65 mould - by Don McDowell - 08-25-2023, 11:33 AM

RE: 40-65 mould - by beltfed - 08-25-2023, 11:43 AM

RE: 40-65 mould - by Kurt - 08-25-2023, 02:55 PM

RE: 40-65 mould - by J.B. - 08-25-2023, 09:36 PM

RE: 40-65 mould - by Steveu - 12-15-2023, 10:29 AM

RE: 40-65 mould - by Kurt - 12-15-2023, 05:24 PM

RE: 40-65 mould - by Steveu - 12-18-2023, 12:51 PM

RE: 40-65 mould - by beltfed - 12-21-2023, 12:33 PM

RE: 40-65 mould - by Kurt - 12-21-2023, 01:16 PM

RE: 40-65 mould - by Steveu - 12-22-2023, 12:50 AM

RE: 40-65 mould - by Kurt - 12-22-2023, 12:27 PM

RE: 40-65 mould - by Steveu - 12-22-2023, 01:35 PM

RE: 40-65 mould - by Kurt - 12-22-2023, 03:20 PM

RE: 40-65 mould - by Steveu - 12-23-2023, 05:16 PM

RE: 40-65 mould - by Don McDowell - 01-19-2024, 10:59 AM

RE: 40-65 mould - by Kurt - 01-19-2024, 12:13 PM

RE: 40-65 mould - by Don McDowell - 01-19-2024, 12:51 PM

RE: 40-65 mould - by Kurt - 01-19-2024, 03:20 PM

RE: 40-65 mould - by Don McDowell - 01-19-2024, 04:04 PM

RE: 40-65 mould - by Steveu - 01-25-2024, 03:16 PM

RE: 40-65 mould - by Don McDowell - 01-25-2024, 03:18 PM

RE: 40-65 mould - by Steveu - 01-25-2024, 04:50 PM

Users browsing this thread: 1 Guest(s)