+- Historic Shooting Forums (http://historicshooting.com)
+-- Forum: General (http://historicshooting.com/forum-1.html)
+--- Forum: The rifles (http://historicshooting.com/forum-2.html)
+---- Forum: Single shot centerfire (http://historicshooting.com/forum-14.html)
+---- Thread: Hey Don (/thread-1859.html)
RE: Hey Don - Old Jim - 04-27-2016
Don,
fire-up the chainsaw and saw open a window in the west wall,
right off the end of your loading bench. Makes for a nice, dry place to shoot from .
Jim
RE: Hey Don - Don McDowell - 04-27-2016
(04-27-2016, 05:14 PM)Kurt Wrote: Heck Don just open the kitchen window if it aint fit outside and lether rip that's what I do LOL.
My chamber is so tight I cant chamber a fired .45-70 case shot in my Shiloh. It sticks out about a 1/2"
I have a die blank and I will run to my friends place and use his lathe to make the die.
Kurt wouldn't it be quicker and easier just to expand the mouths on your 44-75's?
RE: Hey Don - Don McDowell - 04-27-2016
Heck I could shoot off the deck, but 30 degree and 30 mph winds not what I want to mess with in load development.
RE: Hey Don - Kurt - 04-27-2016
(04-27-2016, 06:17 PM)Don McDowell Wrote:(04-27-2016, 05:14 PM)Kurt Wrote: Heck Don just open the kitchen window if it aint fit outside and lether rip that's what I do LOL.
My chamber is so tight I cant chamber a fired .45-70 case shot in my Shiloh. It sticks out about a 1/2"
I have a die blank and I will run to my friends place and use his lathe to make the die.
Kurt wouldn't it be quicker and easier just to expand the mouths on your 44-75's?
The .44-75's are 2.518" long and the .44-100 is 2.6" long
RE: Hey Don - Don McDowell - 04-27-2016
Ok, I thought you said a 45-90
RE: Hey Don - Kurt - 04-27-2016
I did Don, The .44-75 brass is to long for the .45-90.
RE: Hey Don - Don McDowell - 04-27-2016
But couldn't you just run the 45-90 brass into the 44xx size die, then expand the neck out, seat a bullet, firearm and be ready to go?
RE: Hey Don - Kurt - 04-28-2016
All is well.
I got home this afternoon and started on the new rifle to get it ready for Lodi. A week and halve is going to push me getting it ready for oil. I started on the wood and dug through my supply of dies and I have a CH-4D .45-70 sizing die that has a deep throat so it excepts the whole .45-90 case and it just sizes the neck enough that it will seat in the chamber and extracts. A patched bullet one thousand over bore just fits in the case mouth with a firm push. Just about got the chamber to tight. But to tight is better then to loose. I can always make it bigger not smaller
The rechambered .44-90bn.
The Stevens action just about wont allow the wider case rim clear the action to extract. It's very tight but workable. The shorter .44-77 case might be a better option for the CPA action.
Kurt
RE: Hey Don - Don McDowell - 04-28-2016
I was wondering how that 44 2 5/8 was going to work on that action. I sometimes have to thumb the hammer back just a little bit further to get a 45-90 case rim to clear and let the round slide in the chamber.
RE: Hey Don - Kurt - 04-28-2016
The hammer is not the problem, the round trough in front of the hammer. It's not quite wide enough. I took and twisted the rim in some emery cloth a little and that was enough that it cleared the ears.
With a .44-77 case I don't have to do this. Just drop the block and elevate the muzzle and the case will drop out with out a problem because it's shorter then the 90 case. But it works just fine by taking a thousand off the rim diameter.